Interlogix NS2503-24P/2C User Manual Uživatelský manuál stáhnout pdf (Strana 120)

NS2503-24P/2C User Manual

120

If you forget the password, please press the “Reset” button located on the front panel of the

Managed Switch over 10 seconds and then release. Entire settings including VLAN, will be lost

and the Managed Switch will restore to the factory default mode.

The preset user level access privileges for each function is listed under the section titled

Appendix B.

1 2 ... 115 116 117 118 119 120 121 122 123 124 125 ... 196 197

IFS NS2503-24P/2C User 1
TABLE OF CONTENTS 3
Introduction 8
How to Use This Manual 10
Product Features 11
Product Specification 13
INSTALLATION 15
LED Indications 16
Switch Rear Panel 18
Install the Switch 19
Rack Mounting 20
SWITCH MANAGEMENT 23
Management Access Overview 24
Web Management 25
Administration Console 26
Protocols 28
Web-Based Management 29
Requirements 30
Main WEB PAGE 32
System Information 35
Misc Config 36
Console Port Info 40
SNMP Configuration 41
SNMPv3 Groups 44
SNMPv3 View 45
SNMPv3 Access 46
SNMP V3 usm-user 48
Syslog Setting 49
System Log 50
SNTP Setting 51
Firmware Upgrade 52
HTTP Firmware Upgrade 53
Configuration Backup 54
TFTP Backup Configuration 55
Factory Default 56
System Reboot 56
Rate Control 59
Port Status 60
Port Statistics 61
Port Sniffer 62
Protect Port 64
Remote Ping 65
VLAN configuration 66
 Port VLAN ID 67
 Default VLANs 67
Static VLAN Configuration 68
Port-based VLAN 69
802.1Q VLAN 71
VLAN Group Configuration 72
VLAN Filter 75
GVRP VLAN 76
GVRP Setting 77
GVRP Table 78
Q-in-Q VLAN 79
Q-in-Q Port Setting 80
Q-in-Q Tunnel Setting 81
 To configure QinQ Port 81
Trunking 82
Aggregator setting 83
Aggregator Information 84
 LACP enabled 85
 Switch 1 configuration 85
 Switch 2 configuration 86
State Activity 88
Forwarding and Filtering 89
Static MAC Table 90
MAC Filtering 91
IGMP Snooping 92
IGMP Configuration 96
Static Multicast Table 98
Spanning Tree Protocol 100
NS2503-24P/2C User Manual 101
Illustration of STP 103
STP Parameters 104
STP System Configuration 105
 Root Bridge Information 107
Port Configuration 109
DHCP Relay & Option 82 111
Per Port Configuration 114
Access Control List 115
Users Configuration 118
MAC Limit 121
MAC Limit Port Status 122
802.1X Configuration 123
System Configuration 125
802.1x Port Configuration 127
Misc Configuration 128
QoS Configuration 129
QoS PerPort Configuration 132
TOS/DSCP 133
TOS/DSCP Configuration 134
TOS/DSCP Port Configuration 134
Power over Ethernet 136
PoE Schedule 141
CONSOLE MANAGEMENT 143
Configure IP address 144
Commands Level 146
COMMAND LINE INTERFACE 147
System Commands 148
Switch Static Configuration 149
Trunk Configuration 152
VLAN Configuration 154
VLAN Mode: Port-based 155
Administration Configuration 159
IP Configuration 160
Reboot switch 161
Reset to Default 161
TFTP Update Firmware 161
MAC limit 162
Port Mirroring Configuration 163
Quality of Service 164
MAC Address Configuration 165
STP/MSTP Commands 167
System Options 172
Community Strings 172
Trap Managers 173
802.1x Protocol 175
Non-Ipv4 ACL commands 178
Binding 179
Power over Ethernet Commands 180
Configure PoE -- System 182
Configure PoE -- Port 185
(config)# poe priority low 1 186
SWITCH OPERATION 188
POWER OVER ETHERNET OVERVIEW 189
The PoE Provision Process 190
TROUBLE SHOOTING 193
10/100Mbps, 10/100Base-TX 194

Komentáře k této Příručce

Žádné komentáře

Interlogix NS2503-24P/2C User Manual Uživatelský manuál Strana 120

Komentáře k této Příručce

Související produkty a manuály pro Příslušenství komunikace Interlogix NS2503-24P/2C User Manual