Interlogix NS3502-8P-2S User Manual Uživatelský manuál Strana 263
- Strana / 568
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
IFS NS3502-8P-2S User Manual
263
retry to the same server,
send to a different
server, or give up. A
retry to the same server
is counted as a
retransmit as well as a
timeout. A send to a
different server is
counted as a Request as
well as a timeout.
• Other Info
This section contains information about the state of the server and the
latest round-trip time.
Name RFC4668
Name
Description
State - Shows the state of the server. It takes one
of the following values:
Disabled: The selected server is disabled.
Not Ready: The server is enabled, but IP
communication is not yet up and running.
Ready: The server is enabled, IP
communication is up and running and the
RADIUS module is ready to accept access
attempts.
Dead (X seconds left): Access attempts
were made to this server, but it did not
reply within the configured timeout. The
server has temporarily been disabled, but
will get re-enabled when the dead-time
expires. The number of seconds left before
this occurs is displayed in parentheses. This
state is only reachable when more than
one server is enabled.
Round-Tr
ip Time
radiusAuthCli
entExtRoundT
ripTime
The time interval (measured in
milliseconds) between the most recent
Access-Reply/Access-Challenge and the
Access-Request that matched it from the
RADIUS authentication server. The
granularity of this measurement is 100 ms.
A value of 0 ms indicates that there hasn't
- IFS NS3502-8P-2S User 1
- TABLE OF CONTENTS 3
- 1. INTRODUTION 19
- 1.3 How to Use This Manual 22
- 1.4 Product Features 23
- 1.5 Product Specification 26
- - Port Number 27
- 2. INSTALLATION 29
- 2.1.2 LED Indications 30
- 2.1.3 Switch Rear Panel 31
- Power Notice: 32
- 2.2 Install the Switch 33
- 2.2.2 Rack Mounting 34
- IFS Model 36
- SFP Description 36
- 3. SWITCH MANAGEMENT 39
- 3.3 Administration Console 41
- 3.4 Web Management 42
- 4. WEB CONFIGURATION 45
- Default main page 47
- Main Page 48
- 4.2 System 50
- 4.2.1 System Information 51
- 4.2.2 IP Configuration 52
- 4.2.3 IPv6 Configuration 53
- 4.2.4 Users Configuration 54
- Add / Edit User 55
- 4.2.5 Privilege Levels 57
- 4.2.6 NTP Configuration 59
- 4.2.7 UPnP 60
- 4.2.8 DHCP Relay 62
- 4.2.9 DHCP Relay Statistics 64
- 4.2.10 CPU Load 66
- 4.2.11 System Log 67
- 4.2.12 Detailed Log 68
- 4.2.13 Remote Syslog 69
- 4.2.14 SMTP Configuration 70
- 4.2.15 LED Power Reduction 71
- 4.2.16 EEE Power Reduction 72
- 4.2.17 Thermal Protection 73
- 4.2.18 Web Firmware Upgrade 75
- 4.2.19 TFTP Firmware Upgrade 76
- 4.2.20 Configuration Backup 76
- 4.2.21 Configuration Upload 79
- 4.2.22 Factory Default 80
- 4.2.23 System Reboot 81
- 4.3.1 SNMP Overview 82
- 4.3.4.1 SNMPv3 Communities 87
- 4.3.4.2 SNMPv3 Users 88
- 4.3.4.3 SNMPv3 Groups 90
- 4.3.4.4 SNMPv3 Views 91
- 4.3.4.5 SNMPv3 Access 92
- 4.4 Port Management 94
- 4.4.4 Port Statistics Detail 97
- 4.4.5 SFP Information 100
- 4.4.6 Port Mirror 101
- Mirror Port Configuration 102
- Buttons 103
- : Click to save changes 103
- 4.5 Link Aggregation 104
- 4.5.1 Static Aggregation 107
- 4.5.2 LACP Configuration 109
- 4.5.3 LACP System Status 110
- 4.5.4 LACP Port Status 111
- 4.5.5 LACP Port Statistics 112
- 4.6 VLAN 113
- 4.6.2 IEEE 802.1Q VLAN 114
- ■ 802.1Q VLAN Tags 115
- Priority CFI VLAN ID 116
- Original Ethernet Packet 116
- New Tagged Packet 116
- 4.6.3 VLAN Basic Information 117
- 4.6.5 VLAN Membership 123
- 4.6.6 VLAN Membership Status 124
- 4.6.7 VLAN Port Status 126
- 4.6.8 Private VLAN 127
- 4.6.9 Port Isolation 129
- 4.6.10 VLAN setting example: 130
- 4.6.10.3 Port Isolate 135
- 4.6.11 MAC-based VLAN 137
- 4.6.12 MAC-based VLAN Status 138
- 4.6.13 Protocol-based VLAN 139
- 4.7 Spanning Tree Protocol 142
- 4.7.3 Bridge Status 151
- 4.7.5 MSTI Priorities 156
- 4.7.6 MSTI Configuration 157
- MSTI Mapping 158
- 4.7.8 Port Status 160
- 4.7.9 Port Statistics 161
- 4.8 Multicast 163
- Checksum 165
- 4.8.5 IGMP Snooping Status 170
- 4.8.6 IGMP Group Information 172
- 4.8.7 IGMPv3 Information 173
- 4.8.11 MLD Snooping Status 178
- 4.8.12 MLD Group Information 179
- 4.8.13 MLDv2 Information 180
- 4.8.14 MVR 181
- 4.8.15 MVR Status 182
- 4.9 Quality of Service 184
- 4.9.2 Port Policing 185
- 4.9.3 Port Classification 186
- 4.9.4 Port Scheduler 189
- 4.9.5 Port Shaping 189
- 4.9.6 Port Tag Remarking 192
- 4.9.7 Port DSCP 193
- 4.9.8 DSCP-Based QoS 195
- 4.9.9 DSCP Translation 197
- 4.9.10 DSCP Classification 200
- 4.9.11 QoS Control List 201
- 4.9.12 QoS Status 205
- 4.9.14 QoS Statistics 207
- 4.9.16 Voice VLAN OUI Table 210
- 4.10 Access Control Lists 211
- 4.10.3 ACE Configuration 215
- MAC Parameters 217
- IP Parameters 220
- Ethernet Type Parameters 224
- 4.11 Authentication 228
- System Configuration 235
- Port Configuration 238
- Port State 247
- Port Counters 248
- Selected Counters 252
- Attached MAC Address 253
- 4.11.7 RADIUS Overview 258
- RADIUS Accounting Servers 259
- 4.11.8 RADIUS Details 260
- 4.12 Security 275
- 4.12.2 Access Management 279
- 4.12.4 HTTPs 281
- 4.12.5 SSH 281
- 4.12.6 Port Security Status 282
- Port Status 283
- 4.12.7 Port Security Detail 284
- 4.12.8 DHCP Snooping 286
- 4.12.12 ARP Inspection 290
- 4.13 Address Table 293
- 4.14 LLDP 300
- 4.14.3 LLDPMED Configuration 303
- Coordinates Location 304
- Civic Address Location 305
- 4.14.4 LLDP-MED Neighbor 309
- Fast start repeat count 310
- 4.14.5 Neighbor 313
- 4.14.6 Port Statistics 315
- 4.14.7 Port Statistics 316
- 4.15 Network Diagnostics 319
- 4.15.2 IPv6 Ping 320
- 4.15.3 Remote IP Ping Test 321
- 4.15.4 Cable Diagnostics 322
- 4.16.2 Power Configuration 325
- 4.16.3 Port Configuration 329
- 4.16.4 PoE Status 331
- 4.16.5 PoE Schedule 332
- 4.16.6 LLDP PoE Neighbors 334
- 4.16.7 PD Alive-check 335
- 5. COMMAND LINE INTERFACE 337
- Configure IP address 338
- 5.2 Telnet Login 340
- 6. Command Line Mode 341
- System Log Configuration 342
- System Version 343
- System Log Server Mode 343
- System Name 344
- System Contact 344
- System Log Server Address 345
- System Location 345
- System Log Level 346
- System Timezone 346
- System Log Lookup 347
- System Reboot 348
- System Restore Default 348
- System Load 348
- 6.2 IP Command 349
- IP Configuration 349
- IP DHCP 349
- IP Setup 350
- IP Ping 351
- IP DNS Proxy 352
- IPv6 AUTOCINFIG 352
- IPv6 Setup 353
- IPv6 Ping 353
- IP NTP Configuration 354
- IP NTP Mode 355
- IP NTP Server Add 355
- IP NTP Server IPv6 Add 356
- IP NTP Server Delete 356
- Port Mode 357
- Port Flow Control 358
- Port Maximum Frame 359
- Port Power 360
- Port Excessive 360
- Port Statistics 361
- Port VeriPHY 361
- Port SFP 362
- MAC Configuration 363
- MAC Add 363
- MAC Delete 364
- MAC Lookup 364
- MAC Age Time 365
- MAC Learning 365
- MAC Dump 366
- MAC Statistics 366
- MAC Flush 367
- VLAN Configuration 367
- VLAV PVID 368
- VLAN Frame Type 369
- VLAN Ingress Filter 369
- VLAN Mode 370
- VLAN Link Type 370
- VLAN Q-in-Q Mode 371
- VLAN Ethernet Type 371
- VLAN Add 372
- VLAN Forbidden Add 373
- VLAN Delete 373
- VLAN Forbidden Delete 373
- VLAN Forbidden Lookup 374
- VLAN Lookup 374
- VLAN Name Add 375
- VLAN Name Delete 375
- VLAN Name Lookup 376
- VLAN Status 376
- PVLAN Configuration 377
- PVLAN Add 378
- PVLAN Delete 379
- PVLAN Lookup 379
- PVLAN Isolate 380
- 6.7 Security Command 380
- Security Switch User Add 381
- Security Switch User Delete 381
- Example: 383
- Security Switch Auth Method 384
- Security Switch SSH Mode 386
- Security Switch HTTPs Mode 387
- Security Switch Access Mode 388
- Security Switch Access Add 390
- Security Switch Access Clear 392
- Security Switch SNMP Mode 393
- Security Switch SNMP Version 394
- Security Network Psec Switch 412
- Security Network Psec Port 412
- Security Network Limit Mode 414
- Security Network Limit Aging 414
- Security Network Limit Port 415
- Security Network Limit 416
- Security Network NAS Mode 419
- Security Network NAS State 419
- Security Network NAS Agetime 421
- Security Network ACL Action 426
- Security Network ACL Policy 427
- Security Network ACL Rate 428
- Security Network ACL Add 428
- Security Network ACL Delete 430
- Security Network ACL Lookup 430
- Security Network ACL Clear 431
- Security Network ACL Status 431
- Security AAA Configuration 442
- Security AAA Timeout 444
- Security AAA Deadtime 445
- Security AAA RADIUS 445
- Security AAA ACCT_RADIUS 446
- Security AAA TACACS+ 446
- Security AAA Statistics 447
- STP Configuration 448
- STP Version 448
- STP Tx Hold 449
- STP MaxHops 449
- STP MaxAge 450
- STP FwdDelay 450
- STP CName 451
- STP BPDU Filter 451
- STP BPDU Guard 452
- STP Recovery 452
- STP Status 453
- STP MSTI Priority 454
- STP MSTI Map 454
- STP MSTI Add 454
- STP Port Configuration 455
- STP Port Mode 455
- STP Port Edge 456
- STP Port AutoEdge 456
- STP Port P2P 457
- STP Port RestrictedRole 458
- STP Port RestrictedTcn 458
- STP Port bpduGuard 459
- STP Port Statistic 459
- STP Port Check 460
- STP MSTI Port Configuration 460
- STP MSTI Port Cost 460
- STP MSTI Port Priority 461
- 6.9 Link Aggregation Command 461
- Aggregation Configuration 461
- Aggregation Add 462
- Aggregation Delete 462
- Aggregation Lookup 462
- Aggregation Mode 463
- LACP Configuration 463
- LACP Mode 464
- LACP Key 465
- LACP Role 465
- LACP Status 466
- LACP Statistics 466
- 6.11 LLDP Command 468
- LLDP Configuration 468
- LLDP Mode 469
- LLDP Optional TLV 469
- LLDP Interval 470
- LLDP Hold 470
- LLDP Delay 471
- LLDP Reinit 471
- LLDP Statistics 472
- LLDP Info 473
- 6.12 LLDPMED Command 473
- LLDPMED Configuration 473
- LLDPMED Civic 474
- LLDPMED ECS 475
- LLDPMED Policy Delete 475
- LLDPMED Policy Add 475
- LLDPMED Port Policy 477
- LLDPMED Coordinates 477
- LLDPMED Datum 478
- LLDPMED Fast 478
- LLDPMED Info 478
- 6.13 EEE Command 479
- EEE Configuration 479
- EEE Mode 479
- EEE Urgent Queues 480
- PoE Configuration 481
- PoE Mode 481
- AF/AT Mode 482
- PoE Priority 482
- PoE Management Mode 483
- PoE Maximum Power 483
- PoE Allocated Power 483
- PoE Power Supply 484
- PoE Status 484
- 6.15 Thermal Command 485
- Thermal Priority Temperature 485
- Thermal Port Priority 485
- Thermal Status 486
- Thermal Configuration 486
- 6.16 LED Power Command 487
- LED Power Timers 487
- LED Power Delete Timer 487
- LED Power Maintenance 487
- LED Power Configuration 488
- QoS Configuration 488
- QoS Port Classification DPL 489
- QoS Port Classification PCP 490
- QoS Port Classification DEI 490
- QoS Port Classification Tag 491
- QoS Port Classification Map 491
- QoS Port Classification DSCP 492
- QoS Port Policer Mode 492
- QoS Port Policer Rate 493
- QoS Port Policer Unit 493
- QoS Port Scheduler Mode 494
- QoS Port Scheduler Weight 494
- QoS Port QueueShaper Mode 495
- QoS Port QueueShaper Rate 495
- QoS Port QueueShaper Excess 496
- QoS Port Shaper Mode 496
- QoS Port Shaper Rate 497
- QoS Port TagRemarking Mode 498
- QoS Port TagRemarking PCP 498
- QoS Port TagRemarking DEI 499
- QoS Port TagRemarking Map 499
- QoS Port DSCP Translation 500
- QoS Port DSCP Classification 500
- QoS Port DSCP EgressRemark 501
- QoS DSCP Map 501
- QoS DSCP Translation 502
- QoS DSCP Trust 502
- QoS DSCP Classification Mode 503
- QoS DSCP EgressRemap 503
- QoS Storm Unicast 504
- QoS Storm Multicast 504
- QoS QCL Add 505
- QoS QCL Delete 506
- QoS QCL Lookup 506
- QoS QCL Status 507
- QoS QCL Refresh 507
- 6.18 Mirror Command 508
- Mirror Configuration 508
- Mirror Port 508
- Mirror Mode 509
- 6.19 Configuration Command 510
- Configuration Save 510
- Configuration Load 510
- 6.20 Firmware Command 511
- Firmware Load 511
- Firmware IPv6 Load 511
- Firmware Information 511
- Firmware Swap 511
- 6.21 UPnP Command 512
- UPnP Configuration 512
- UPnP Mode 512
- UPnP TTL 513
- UPnP Advertising Duration 513
- 6.22 MVR Command 513
- MVR Configuration 513
- MVR Group 514
- MVR Status 514
- MVR Mode 515
- MVR Port Mode 515
- MVR Multicast VLAN 516
- MVR Port Type 516
- MVR Immediate Leave 517
- 6.23 Voice VLAN Command 517
- Voice VLAN Configuration 517
- Voice VLAN Mode 518
- Voice VLAN ID 519
- Voice VLAN Agetime 519
- Voice VLAN Traffic Class 520
- Voice VLAN OUI Add 520
- Voice VLAN OUI Delete 521
- Voice VLAN OUI Clear 521
- Voice VLAN OUI Lookup 522
- Voice VLAN Port Mode 522
- Voice VLAN Security 523
- 6.24 IPMC Command 523
- IPMC Configuration 523
- IPMC Mode 524
- IPMC Flooding 524
- IPMC Leave Proxy 525
- IPMC Proxy 525
- IPMC State 526
- IPMC Querier 527
- IPMC Fastleave 527
- IPMC Throttling 528
- IPMC Filtering 528
- IPMC Router 529
- IPMC Status 529
- IPMC Group 530
- IPMC Version 530
- IPMC SSM 531
- IPMC Parameter RV 531
- IPMC Parameter QI 532
- IPMC Parameter QRI 532
- IPMC Parameter LLQI 533
- IPMC Parameter URI 533
- VCL Status 535
- VCL Protocol-based VLAN Add 537
- 7. SWITCH OPERATION 538
- 7.5 Auto-Negotiation 539
- What is PoE? 540
- The PoE Provision Process 542
- Line Detection 543
- Classification 543
- Start-up 543
- Operation 543
- 9. TROUBLE SHOOTING 545
- 1 2 3 4 5 6 7 8 548
- APPENDEX B: GLOSSARY 549
Související produkty a manuály pro Příslušenství komunikace Interlogix NS3502-8P-2S User Manual
Příslušenství komunikace Interlogix GE-DSSG-244-POE Installation Guide Uživatelský manuál
(10 stránky)
(10 stránky)
Příslušenství komunikace Interlogix NS4702-24P-4S-4X Command Line Guide Uživatelský manuál
(434 stránky)
(434 stránky)
Příslušenství komunikace Interlogix GE-DSH-73 Series Installation Sheet Uživatelský manuál
(13 stránky)
(13 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce