Interlogix Concord 4 REV J Installation Manual Uživatelský manuál Strana 29
- Strana / 153
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 2: Installation
Concord 4 Installation Manual 23
Figure 15: Installing SuperBus 2000 modules
SuperBus 2000 2-amp power supply (600-1019)
Refer to the power supply documentation for the mounting procedure. Connect
the power supply to the panel terminals and devices to be powered as shown in
Figure 16 below.
Note: Do not connect power (AC and battery) to the power supply until the panel
is ready for power-up. For power supply AC and battery connections, refer to the
power supply documentation.
Figure 16: Wiring the SuperBus 2-amp power supply to the panel
Panel terminals
Power supply terminals
To power inputs on devices
GND +12V A BUS B
SuperBus 2000 transceiver modules
The transceiver expands RF reception range when placed near sensors on the
fringe of panel RF reception. Refer to the transceiver documentation for mounting
information.
Connect the transceiver (up to four) to the panel as shown in Figure 17 on page
24.
- P/N 466-2182 • REV J • NOV12 1
- Content 3
- Important information 5
- Chapter 1 7
- Introduction 7
- Planning the installation 8
- SuperBus 2000 bus devices 9
- Chapter 1: Introduction 10
- Chapter 2 11
- Installation 11
- Installation overview 12
- Chapter 2: Installation 13
- Chapter 2: Installation 14
- Mounting the panel 16
- Grounding the panel 17
- Antenna shrouds 18
- Optional SnapCards 19
- Panel terminals 20
- Intrusion detection devices 21
- Smoke detectors 21
- Four-wire smoke detectors 23
- Speakers and sirens 24
- SPKR SPKR SPKR SPKR 25
- Not used 25
- To zone input 26
- SuperBus 2000 touchpads 28
- SuperBus 2000 modules 28
- Power supply terminals 29
- To power inputs on devices 29
- GND +12V A BUS B 29
- Hardwired interior 32
- RJ31X phone jack 34
- AC power transformer 36
- Backup battery 37
- Power up 37
- Chapter 3 39
- Programming 39
- Overview 40
- Programming touchpad 41
- Quick programming mode 42
- Tier 1 programming menus 43
- DEMO KIT MODE OFF/ON (new 44
- Chapter 3: Programming 45
- Tier 2 programming menus 46
- Shortcut numbers 50
- Security menu 51
- KEYCHAIN TP PTN), then 54
- PARTITION 54
- Phones menu 56
- PHONE NUMBER _ 57
- NUMBER _ 58
- Phone options menu 60
- Timers menu 63
- SLEEP TIME 64
- NO USAGE 64
- Light control menu 65
- Touchpad options menu 66
- Reporting menu 67
- Siren options menu 72
- Sensors menu 73
- S01 P1 G13 NC HW BACK DOOR 75
- EDIT SENSORS 75
- SENSOR GROUP nn 75
- Audio verification menu 77
- AUDIO VERIFY 78
- Accessory modules menu 79
- DEVICE ID (current ID) 80
- DEVICE PTN and then press 80
- PARTITION ASSIGN n 80
- OUTPUTS 81
- OUTPUT 1 81
- PARTITION ASSIGN 1 81
- CONFIGURATION tttrr 81
- Onboard options menu 84
- Macro keys menu 87
- User programming mode 88
- Time and date menu 89
- User codes menu 90
- Options menu 93
- Set up schedules menu 94
- Energy saver menu 98
- Downloader programming 99
- Chapter 3: Programming 100
- Chapter 4 101
- Testing and 101
- Testing the system 102
- Zones/sensors 103
- Phone communication 104
- Outputs and sirens 106
- Light control 107
- Energy saver module (ESM) 107
- Touchpad display contrast 108
- Troubleshooting 112
- Access code issues 114
- Arming and disarming issues 114
- Bypassing issues 115
- Alphanumeric touchpad issues 116
- Speaker issues 117
- Siren issues 117
- Hardwired zone issues 118
- Wireless sensor zone issues 118
- Wireless touchpad issues 119
- Phone issues 119
- Light control issues 120
- Energy saver module issues 120
- Automation module issues 121
- Appendix A 123
- System planning sheets 123
- Customer information 124
- Wireless devices 124
- Hardware devices 125
- Zone and sensor assignments 127
- Appendix B 135
- Reference tables 135
- Sensor group characteristics 136
- Appendix B: Reference tables 138
- Cross-zoning 139
- Sensor text 140
- System event triggers 142
- Sensor group event triggers 143
- Sensor number event triggers 144
- Response characteristics 149
- Response numbers 149
- Specifications 151
Související produkty a manuály pro Kontrolní panel Interlogix Concord 4 REV J Installation Manual
Kontrolní panel Interlogix NX-4 Uživatelský manuál
(44 stránky)
(44 stránky)
Kontrolní panel Interlogix NX-4 Uživatelský manuál
(18 stránky)
(18 stránky)
Kontrolní panel Interlogix NX-6 Uživatelský manuál
(18 stránky)
(18 stránky)
Kontrolní panel Interlogix NX-8 Uživatelský manuál
(61 stránky)
(61 stránky)
Kontrolní panel Interlogix NX-8 Uživatelský manuál
(18 stránky)
(18 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce